友 情 链 接

中科院金属研究所

沈阳材料科学国家(联合)实验室

  研究部主任李殿中博士简介

 
    李殿中,男,1966年5月生,工学博士,研究员,博士生导师,中国科学院金属研究所沈阳材料科学国家(联合)实验室材料加工模拟研究部主任。中国材料研究学会计算材料学分会主席。1998年入选中国科学院“百人计划”,2007年获何梁何利科学与技术创新奖。
 
  主要工作经历
 
    1989年毕业于哈尔滨工业大学材料科学与工程系,获学士学位。
 
    1992年毕业于原机械工业部沈阳铸造研究所,获硕士学位。
 
    1992-1997年在沈阳铸造研究所工作,主要从事凝固过程微观组织模拟与实验研究工作。
 
    1998年毕业于哈尔滨工业大学,获博士学位,同年入选中科院“百人计划”。作为学科带头人,从事凝固与热变形过程的工艺与组织演变的计算机模拟工作。
 
    2001年作为英国皇家学会高级访问学者,在伯明翰大学著名教授John Campbell指导下开展热加工过程组织模拟与工艺设计工作。
 
    目前在中国科学院与英国皇家学会的支持下,与英国伯明翰大学成立了中英联合高技术铸造中心。作为负责人之一,主要负责大型铸锻件的模拟和工艺设计工作,致力于攻克关键铸锻件产品的核心制造技术。
  主要学术贡献
 
    李殿中研究员一直从事材料制备工艺和计算机模拟工作,致力于凝固与热成形过程的组织性能预报与工艺优化。先后承担国家和企业委托重大课题多项,突破了船用曲轴毛坯锻造、大型支承辊铸造、大型空心钢锭铸造、三峡水轮机组不锈钢转轮铸钢件铸造等关键技术,初步实现了国产化。作为主要负责人完成了高温合金等轴晶叶片凝固组织模拟与工艺优化课题。研究成果在沈阳黎明发动机公司应用后,叶片合格率提高一倍,开发的新工艺从96年应用至今,每年创造直接经济效益约200万元。目前与中国一重集团公司合作开发的轧钢用50t铸钢支承辊在国内首次浇注获得成功,并且在太原不锈钢生产线成功应用。与上海重型机器厂有限公司和鞍钢重机合作开发了大型船用曲轴毛坯制造技术,采用该技术,上述两家上重型企业已经成功生产了50t曲轴毛坯,为曲轴制造国产化作出了贡献
  荣誉与奖励  
 
    何梁何利科学与技术创新奖
 
    辽宁省科技发明一等奖1项(第1完成人);
 
    河北省科技进步一等奖1项(第3完成人);
 
    国家科技进步一等奖1项(第9完成人)。
  代表性论文  
      在Acta Materialia, Scripta Materialia, Metallurgical Transaction A, Journal of Materials Research等各种核心刊物上发表论文80余篇,合著专著1部,国际会议邀请报告2次。

1. D.Z. Li, N.M. Xiao,Y.J. Lan, C.W. Zheng and Y.Y. Li. Growth modes of individual ferrite grains in the austenite to ferrite transformation of low carbon steels. Acta Mater, 55, 2007, 6234-6249.

2. N. M. Xiao, M. M. Tong, Y. J. Lan, D. Z. Li and Y. Y. Li: Coupled simulation of the influence of austenite deformation on the subsequent isothermal austenite–ferrite transformation. Acta Mater, 54, 2006, 1265-1278.
3. Y.J. Lan, N.M. Xiao, D.Z. Li and Y.Y. Li: Mesoscale simulation of deformed austenite decomposition into ferrite by coupling a cellular automaton method with a crystal plasticity finite element model. Acta Mater, 53, 2005, 991-1003.
4. Y. J. Lan, D. Z. Li and Y. Y. Li: Modeling austenite decomposition into ferrite at different cooling rate in low-carbon steel with cellular automaton method. Acta Mater, 52, 2004, 1721-1729.
5. Tong MM, Li DZ and Li YY. A q-state Potts model-based Monte Carlo method used to model the isothermal austenite-ferrite transformation under non-equilibrium interface condition. Acta Mater, 53, 2005, 1485-1497.
6. M. M. Tong, D. Z. Li and Y. Y. Li: Modeling the austenite–ferrite diffusive transformation during continuous cooling on a meso-scale using Monte Carlo method. Acta Mater, 52, 2004, 155-1162.
7. Liu ZX, Li DZ, Qiao GW and Li YY. Nanometer Martensite flakes in high temperature deformation-induced ferrite grains of a low carbon steel. Scripta Mater, 56, 2007, 777-780.
8. Xiao NM, Zheng CW, Li DZ and Li YY. A simulation of dynamic recrystallization by coupling a cellular automaton method with a topology deformation technique. Computational Materials Science, 41, 2008, 366-374.
9. Liu ZX, Li DZ, Lu SP and Qiao GW. Thermal stability of high temperature deformation induced ferrite in a low carbon steel. ISIJ Inter, 47, 2007, 289-294.
 

沈阳材料科学国家(联合)实验室

地址:沈阳市文化路72号(110016)